How much is the bulk density of hydrating (blended) cement paste?

In the last post, I explained the clear definition of different densities. Among these densities, bulk density and apparent density are the two most important values when performing mercury intrusion porosity (MIP) experiment. Since samples that undergo MIP are usually irregular, the bulk volume is not possible to measure without being immersed in liquid. By the help of MIP, the bulk volume can be measured, thus the bulk density can be calculated simply dividing the mass by bulk volume. ...

2013-03-19 · 2 min · 332 words · Cement Science

What is density? how to distinguish different density definitions?

As material researchers, we know density is the physical property of materials. Even since grade school, we are taught that density is simply the mass of an object divided by its volume. However, this is pretty complicated in the case of cementitious materials. The mass of a certain amount of harden cement (or concrete) paste is a finite value, but how about the volume? since the harden cement paste is porous, how do we consider the open and close pores inside the paste as we want to determine the volume? ...

2013-03-06 · 2 min · 410 words · Cement Science

Sample Preparation for Quantitative X-Ray Diffraction (XRD/Rietveld)

Theoretical background: see chapters 3 and 4 in Lieven Machiels’s PhD thesis (2010). Sample preparation method modified from Machiels et al. (2008). Representative sampling The mineralogy and glass content of slags depend largely on the mode of cooling of the slags, e.g. slow cooling in a slag pot can result in a large amount of crystalline phases, and fast granulation in water can result in high glass content. A mineralogical analysis will thus only represent the mineralogy of a slag system for a certain grade of cooling and strongly different results can be obtained when cooling conditions are different between the different batches. ...

2013-01-22 · 3 min · 504 words · Cement Science

Determining the Amount of Reacted Slag in Blended Cement Using EDTA Method

1 Procedure of EDTA A typical chemical reaction of a slag could be like the following [NIST, D.P Bentz], C7.88S7.39M3A + 2.6CH + bH → 7.39C1.42SHmA0.046 + 0.66M4.6AHd C=CaO, S=SiO2, M=MgO, A=Al2 O3, CH=Ca(OH)2, H=H2O. The method EDTA (Ethylenediaminetetraacetic acid) has been described by Erntroy [Erntry, 1987]. The following is a short description of the method. 93.0g of disodium EDTA 2H2O is dissolved in a mixture of 250 ml triethanolamine and 500 ml water. The solution is transferred to an volumetric flask; 173 ml of diethylamine added and the mixture made up to 1000 ml with water; For the extraction, 50 ml of the above solution is pipetted into a beaker and diluted to approximately 800 ml with water; The solution is brought to a temperature of 20.0±2 ◦C and 0.5 g of the dried and powdered sample paste, weighed to the nearest 0.0001 g, sprinkled over its surface; The solution is stirred for 120 ± 5 min while maintaining the stated temperature and is then filtered under vacuum through a 90 mm diameter Whatman GF/C filter which had been previously washed with 100 ml of distilled water, dried and weighed; The residue is then washed 5 times with 10 ml lots of distilled water, fried at 105 ◦ C for 1 hour and weighed to the nearest 0.0001 g. Calculation of reaction degree of slag. 2 Calculation of reaction degree of slag ...

2012-12-02 · 3 min · 511 words · Cement Science

Hydration Mechanisms of Portland Cement: Topochemical or Through-Solution Reaction?

When we simulate the hydration process of Portland cement, it is of significant importance to know the hydration mechanisms. Basically, there are two mechanisms for the hydration of Portland cement, viz. Topochemical and Through-Solution Reaction. 1 Topochemical Reaction Concept Immediately after the first contact of the cement with water a calcium-rich silicious clinker would liberate Ca2+ ions into the solution. A calcium-poor skeleton is left which reacts with the calcium-rich solution which is accompanied by swelling of the hydration products compared with the original volume of the anhydrous cement. The topochemical concept was launched by Michaelis at the beginning of last century. Since then topochemical phenomena have been reported for the hydration of both C3S and Portland cement. ...

2012-11-22 · 3 min · 503 words · Cement Science